Specialty Solutions Product

PD IronWith a ProSeries Iron & Hydrogen Sulfide Removal System, a home and lifestyle can benefit in and number of ways.

A Plumber’s Direct Iron Removal with Aeration Filtration System is a durable, dependable system designed to help treat problem water.  Depending on your needs, the system may be used independently or in tandem with other systems.

BENEFITS

  • Eliminates stains, discolored water and odors with the oxidative power of air
  • Guards pipes and plumbing fixtures against corrosive iron build-up
  • Clean Media Technology extends the life of the filtration media and prevents bacteria growth inside the tank
  • Safe for septic systems, plumbing and appliances
  • Uses only air and water in the regeneration cycle – no chemicals or salt
  • Removes iron, manganese, hydrogen sulfide gas, tannins and many unregulated water toxins.
  • Provides a steady supply of clean, fresh water with minimal maintenance
  • Protects bathing, showering and cooking water against common toxins that can be absorbed through the skin or inhaled in moist air

FEATURES

The computerized control of this system is directed and monitored by our proprietary control head.  It can be programmed to meet your personal quality and usage requirements.  It also stores data to allow for proper monitoring and maintenance of the system.  There is never any down time during regeneration because the system goes into automatic bypass when regeneration is required, so you will never be out of water.

Dual layer construction of this durable tank is comprised of miles of glass filament for exemplary strength.  Inside this tough exterior there’s another tank made of sanitary plastic which insures that your drinking water will never contact the exterior fiberglass surface.

HOW IT WORKS

Step 1: Water enters the compressed aeration chamber.  As the water passes through the chamber, the water becomes highly oxygenated.  As the water continues to flow through the tank, the oxygenated water converts the iron and manganese from dissolved minerals and gasses to physical particles.

Step2: The highly oxygenated water then flows through the multimedia filter bed where iron and manganese are trapped in the multimedia bed.

Step3: At pre-determined intervals the system will backwash and reduce all contaminants from the filter bed.

LIMITATIONS OF USE

This system is designed for use on water supplies containing low levels of hydrogen sulfide, medium levels of iron and manganese levels not greater than 2.0 ppm. 

pH: The influent water must be between 6.8 and 9.0.

Iron Bacteria: If iron bacteria are present, frequent service may occur and the life of the system may be limited. By properly controlling the iron bacteria with chlorine or other approved methods for bacteria reduction, the system will function properly.

Manganese: Maximum influent manganese concentration is 2.0 ppm; amounts over 2.0 ppm may gradually prevent iron removal.  For optimum manganese reduction, the pH should be between 8.0 and 9.0.  If both iron and manganese are present, the pH should be between 8.0-8.5.

Organic Matter (tannins): The presence of organics above 2.0 ppm may hinder the operation of the system.

Chlorine: The presence of chlorine in the raw water supply should be limited to a maximum of 1.0 ppm.

MAINTENANCE REQUIRMENTS

The valve on your system is designed to last a lifetime.  Occasionally it may require cleaning and lubrication of the moving parts.  Your water quality and the amount of regenerations will affect this schedule.

The media will eventually become exhausted or consumed and will need replacement.  Replacement schedules depend on the incoming water quality and your water usage. 

CALIFORNIA RESIDENTS: Water treatment devices sold to consumers in California accompanied by certain health claims must be certified by the California Department of Health Services.  The Plumber’s Direct Iron Removal Filters are not certified by the State of California for the purposes of making health claims.

Benefits will be provided by various types of Plumber’s Direct equipment when installed and operated according to manufacturer’s recommendations.  Operational, maintenance and replacement requirements are essential for the product to perform as advertised.  All claims based on best available information at time of printing.  Manufacturer makes no representation as to the suitability of this equipment for a particular application.